| Number | Title |
| BN-DG-A1 | Capacity of Drums with Korborgen Heads |
| BN-DG-A10 | Determining 4 Inch ANSI Pipe Tower Davits (4 Shts), Chart for |
| BN-DG-A11 | Determining Legs for Vertical Vessels With 4 Legs, Chart for |
| BN-DG-A12 | Anchor Bolts Locations for Vessels With Legs, Instructions for |
| BN-DG-A13 | Weights of ANSI Connections Blind Flanges and Manways |
| BN-DG-A2 | Weights of Vessel Shells |
| BN-DG-A3 | Weights of Korbogen Heads (Thickness 6 to 27 mm Incl.) (2 Sheets) |
| BN-DG-A4 | Reinforcing Rings for Shell and Korbogen Heads |
| BN-DG-A5 | Curves for Quick Determination of Nozzle Projection 2 Inch thru 6 Inch (3 Sheets) |
| BN-DG-A6 | Schedule List for ANSI Pipes for Vessel Nozzles |
| BN-DG-A7 | Nomogram for Determining Integral Truss Size Max. Allowable Span and Min. Tray Spaces for Sieve and Valve Type Stainlesssteel Trays 'cold Condition' |
| BN-DG-A8 | EX, IX & WX for Angle Type Integral Trusses of Various Plate thicknesses (2 Sheets) |
| BN-DG-A9 | 'l' Max for Angle Type Truss Sizes Under Operating Conditions for S.S. Trays |
| BN-DG-C1 | Plant Layout |
| BN-DG-C10 | Model Estimating and Cost Control |
| BN-DG-C11 | Model Final Data |
| BN-DG-C12 | Checking a 3D PDS Piping Model and Definition of Percentage Completion |
| BN-DG-C13 | Conducting 3D PDS Piping Model Reviews |
| BN-DG-C1A | Plant Layout - General Requirements, Section A |
| BN-DG-C1B | Plant Layout - Pipeway Design, Section B, |
| BN-DG-C1C | Plant Layout - Relief System Design, Section C, |
| BN-DG-C1D | Plant Layout - Columns, Section D, |
| BN-DG-C1E | Plant Layout - Exchangers, Section E, |
| BN-DG-C1F | Plant Layout - Compressors and Drivers, Section F, |
| BN-DG-C1G | Plant Layout - Fired Heaters, Section G, |
| BN-DG-C1H | Plant Layout - Cooling Water Towers, Section H, |
| BN-DG-C1J | Plant Layout - Storage and Loading, Section J, |
| BN-DG-C1K | Plant Layout - Pumps, Section K, |
| BN-DG-C3 | Design the Preparation of Piping Design Documents |
| BN-DG-C34 | Flgd. Contr. Vlv. Piping Manifold 150, 300 - 600 Lb Gate Vlvs. CS |
| BN-DG-C35 | Flgd. Contr. Vlv. Piping Manifold 150, 300 - 600 Lb Gate Vlvs. Mss Stub Ends. |
| BN-DG-C4 | Preparation of Design Models |
| BN-DG-C5 | Conducting Model Reviews |
| BN-DG-C6 | Design Model and Definition of Percentage Completion, Checking of |
| BN-DG-C7 | Design Model Photographs |
| BN-DG-C8 | Health/safety Requirements for the Model Shop |
| BN-DG-C9 | Packing and Shipping of Design Models |
| BN-DG-DS1 | Ladders - Dimensions From Holes to Center Line Vessel |
| BN-DG-DS10 | Platforms - Bracket Location |
| BN-DG-DS11 | Top Platforms - Location of Supports |
| BN-DG-DS13 | Supports for Horizontal Heat Exchangers Sheet 1 |
| BN-DG-DS14 | Supports for Horizontal Heat Exchangers Sheet 2 |
| BN-DG-DS20 | Exchanger Support - Type 1 |
| BN-DG-DS21 | Exchanger Support - Type 2 |
| BN-DG-J1 | Radii of Curves for Plant Roads |
| BN-DG-J10 | Miscellaneous Standard Details |
| BN-DG-J2 | Typical Foundation and Anchor Bolt Location Plan Withloading Tables |
| BN-DG-J3 | Bar Bending, Table for |
| BN-DG-J5 | Piling Plan Example Drawing |
| BN-DG-J6 | Foundation Location Plan Example Drawing |
| BN-DG-J7 | General Instructions for Piling Plans and Foundations Location Plans |
| BN-DG-J8 | Concrete Plinths for Horizontal Equipment |
| BN-DG-J9 | Concrete Plinths for Horizontal Vessels |
| BN-DG-K1 | Instrument Main Panel Construction |
| BN-DG-K1-14 | Instrument Connections on Vessels |
| BN-DG-K10 | Instrument Schematic Diagrams |
| BN-DG-K11 | Instrument Installation Details |
| BN-DG-K13 | Instrument Cable List |
| BN-DG-K4 | Instrument Logic Symbols |
| BN-DG-K5 | Instrument Air Piping Details |
| BN-DG-K6 | Typical Field Layout of Instruments |
| BN-DG-K7 | Instrument Wiring Diagram |
| BN-DG-K8 | Document Relation Plan |
| BN-DG-K9 | Instrument Process Piping Details |
| BN-DG-T1 | Standard Types of Fixed Tube Sheet Exchangers(2 Sheets) |
| BN-DG-T1-16 | Determining Dimensions of Heat Exchangers (Float Head Type) (3 Sheets) |
| BN-DG-T11 | Typical Detail Floating Head, Cover Flange and Backing Ring |
| BN-DG-T12 | Orientation of Pass Partitions |
| BN-DG-T13 | Min.Dome Heights for Tube Layout |
| BN-DG-T14 | Baffle & Support Plate Thicknesses and Clearances In Acc Tema 'R' |
| BN-DG-T15 | Drilling Dimensions of Tube Holes |
| BN-DG-T17 | Tube Layout Pitches |
| BN-DG-T19 | Tube Sheet Dimensions for Unit In Acc.With Tema Class 'R' (2 Sheets) |
| BN-DG-T2 | Bundle Retainer for Reboiler (Kettle Types) |
| BN-DG-T3 | Dimensions of Standard Heat Exchangers |
| BN-DG-T4 | Dimensions of Standard Heat Exchangers In Inches |
| BN-DG-T5 | Outer Tube Limit Dimensions of Standard Heat Exchangers |
| BN-DG-T6 | Outer Tube Limit Dimensions of Standard Heat Exchangers In Inches |
| BN-DG-T7 | Numbering and General Notes of Welding Neck Girth Flanges for Heat Exchangers |
| BN-DG-UD008 | Design Guide for the Drafting of Flow Diagrams |
| BN-DG-UD01 | Checking of Flow Diagrams and line designation tables |
| BN-DG-UD02 | Checking of Plotplans and Plant Layouts |
Design Guides 
